15.2 C
New York
Friday, September 29, 2023

Buy now

Why My Netgear Router Firmware Update Taking Forever?

Firmware is the operating system or software on the device that helps it perform its functions. The firmware on the Netgear router needs to be updated regularly to make the most out of the router. But often users face issues while updating the firmware on the router. This article is meant to address the issue wherein Netgear router firmware update takes forever. At times, due to various reasons, the firmware update on the router gets stuck and takes like ages to complete. We are going to help you fix this issue and let you know why it actually happens. To know more about it, continue reading.

Why Netgear Router Firmware Update is Stuck?

Before we help you fix the issue that you are currently facing, we would want you to know the reason why it happened in the first place. Knowing the causes is also important such that you don’t get stuck again with the same issue in the future. So let us tell you the reasons that are mostly behind causing the firmware update stuck issue.

  • Power Supply Issues

The power supply to the Netgear router as well as the device used plays an important role during the firmware update process. Perhaps the power supply got interrupted when the firmware update was happening and thus the process got stuck. Thus, you need to check the power adapter of the router if it is damaged. Plus it should be inserted properly into the router as well as the power socket. You should check the power socket too. Maybe it is damaged. Try plugging the router into some other power socket now. Observe the power LED on the router. It will help you understand the power supply. Simply put, you need to make sure that the power supply to the router and the device should be adequate during the entire firmware update process.

  • Faulty Internet Connection

Another reason that can make your firmware update process take like forever is a faulty internet connection. You should check with your ISP if there is an internet-related issue going on from his end. If her agrees to this, give him some time to get it fixed, and then try updating the firmware again. Another thing that you need to check is that if you have connected the Netgear router to the modem through a wireless connection, then the router must be placed within the modem’s range. However, if you have connected them using the Ethernet cable, then check the cable once. Maybe it is worn out or is making a loose connection. Replace the cable if it is damaged and insert it properly to make a firm connection between the router and the modem.

  • Wrong Firmware Updated

Apart from the two reasons mentioned above, another cause is updating the wrong firmware on the router. In case you are trying to update the firmware manually, then you first need to download it on your PC. Here you need to be very careful that you are downloading the correct firmware file that is meant for the Netgear router model that you have. For instance, if you have done a Netgear AC1600 setup at your home, then download the firmware file for this model only. Otherwise, the firmware may get corrupted.

  • Firmware Update Interrupted

While you are updating the firmware on your Netgear router, you need to take care of the point that after you have begun installing the firmware file on the router, you are not supposed to interrupt the process in any way. You need to remain on the Netgear Genie dashboard the whole time. Opening a new tab on the browser can also cause an interruption to the process. Thus refrain from doing any other task on the PC and do not refresh the page. The firmware installation process will take a while to get done. You need to be patient here.

Fixed: Netgear Router Firmware Update Stuck Issue

Reboot the Netgear Router

In case you are stuck with the firmware update process and it is taking so much time then you need to reboot the router. Simply power off the router. Unplug it from the wall socket. You need to plug it in back only after waiting for a couple of minutes. After you have turned the power button on the router on, access the Netgear router admin panel using the Netgear default IP address. Here you need to check if the firmware has been updated or not.

To Briefly Conclude

We are very sure that by following the above steps you have come out of the mess that you were currently stuck with. If the firmware has yet not been updated then reset the router and update the firmware by keeping all the points mentioned above into consideration.

Check Also: Brief Information About Netgear Router Remote Management!

Related Articles

LEAVE A REPLY

Please enter your comment!
Please enter your name here

[td_block_social_counter facebook=”tagdiv” twitter=”tagdivofficial” youtube=”tagdiv” style=”style8 td-social-boxed td-social-font-icons” tdc_css=”eyJhbGwiOnsibWFyZ2luLWJvdHRvbSI6IjM4IiwiZGlzcGxheSI6IiJ9LCJwb3J0cmFpdCI6eyJtYXJnaW4tYm90dG9tIjoiMzAiLCJkaXNwbGF5IjoiIn0sInBvcnRyYWl0X21heF93aWR0aCI6MTAxOCwicG9ydHJhaXRfbWluX3dpZHRoIjo3Njh9″ custom_title=”Stay Connected” block_template_id=”td_block_template_8″ f_header_font_family=”712″ f_header_font_transform=”uppercase” f_header_font_weight=”500″ f_header_font_size=”17″ border_color=”#dd3333″]
- Advertisement -spot_img

Latest Articles