Netgear Nighthawk router is one of the best networking solutions when it comes to accessing continuous internet all over the house or increasing existing WiFi coverage to great extent. There is nothing like the Nighthawk router. So, if you are looking for a WiFi device to satisfy your daily internet needs, just opt to configure it via Nighthawk router login details.
But, hold on! There is nothing perfect in this world, is it? Even your Netgear Nighthawk router has a few issues. And, one of the most seen issues is the “Nighthawk router orange light” issue.
Are you also experiencing the same issue? Need not worry! The hacks provided in this post will vanish the issue for you as it never existed before. So, continue reading!
Fixed: Nighthawk Router Orange Light Issue
Fix 1: Check the Ethernet Connection
The first fix that you need to apply to troubleshoot the issue is to check the Ethernet connection you have established between your Netgear Nighthawk router and modem. Ensure that the cable connection is not loose.
Bear in mind, a loose or improper Ethernet connection leads to “Nighthawk router orange light” issue. Apart from this, you also have to make sure that the Ethernet cable used by you is not damaged. If you notice any sort of damages in it, replace it right away.
Now, after applying this fix, see if you are able to troubleshoot the issue or not. In case not! Don’t be hopeless! The second hack is waiting for you. Apply it in order to make the most out of your Nighthawk router and fix issues with it.
Fix 2: Verify Your WiFi Connection
If the above-mentioned fix doesn’t bring you luck, then make sure that you have a stable WiFi connection. Yes, you read it right! Internet connection (if poor) leaves a big impact on your:
- Netgear Nighthawk router itself! Means, your router’s performance may degrade!
- And, modem and router connection, resulting in “Nighthawk router orange light” issue.
Make sure everything is fine from your service provider’s end. You can try improving your internet speed by upgrading your existing data plan. Apart from this, ensure that your router’s firmware is up-to-date as well.
Fix 3: Relocate Your Nighthawk Router
If you are unable to fix “Nighthawk router orange light” issue by following the hacks listed above, relocate it (the router). Most probably, changing the router’s location will help you to troubleshoot the issue.
You need to choose a location for your Netgear Nighthawk router that is:
- Closer to your existing modem
- On a higher shelf
- Ventilated area
- Not inside cabinet, back of PC, or beneath table
Thus, after relocating your Nighthawk router, you can anticipate that the “Nighthawk router orange light” issue will be resolved.
If you are unfortunately getting the same issue, then do the following:
Fix 4: Power Cycle Your Nighthawk Router
At times, your Netgear Nighthawk gets tired or overheated. In such a scenario, you must power cycle or restart your router once. For this:
- Simply disconnect your Nighthawk router and modem, and then, power it off. For this, you need to unplug it.
- Leave the router unplugged for several minutes and then, you can plug it back again.
- After putting your Netgear Nighthawk router on power, reconnect it to your modem and see if the issue is fixed for you or not.
However, if power cycling hasn’t resolved the issue for you, then you need to reset your Netgear Nighthawk router back to factory default values. The reason being, your router isn’t properly configured and improper configuration is one of the biggest causes behind getting the brainteaser issue you are currently experiencing.
Fix 5: Reset Your Nighthawk Router
Note: Take the backup of router’s settings prior to resetting it.
- Press and locate the router’s reset hole.
- Once found, press, hold, and release it.
- Your router resets successfully.
What happened? Getting issues while resetting your Netgear Nighthawk router? No worries! Simply ensure that:
- Your router is receiving continuous power. In simple words, do not unplug it.
- You have disconnected your modem and Nighthawk router before applying the reset process.
And, there you are! The Netgear Nighthawk router resets successfully. Now, reconfigure it via routerlogin.net web address, routerlogin details (default), and applying the instructions provided on Netgear Genie setup wizard.
By any chance, if the default details routerlogin not working for you, we suggest you see the manual of your device.
Now, we really hope that after applying the hacks provided in this post, you are able to say goodbye to “Nighthawk router orange light” issue. So, please share with us – which hack helped you out. One, two, or all of them!
